18V ONE+ HP Brushless 30-34° Framing Nailer (RFN1830X)

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer does not require air charging before use. It is ready to operate straight out of the box—simply insert a fully charged battery, load compatible framing nails, and start working. This cordless…

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer features Air-Strike technology, eliminating the need for gas cartridges or an external compressor. It uses compressed air stored inside the tool and is powered by a RYOBI ONE+ battery for…

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer operates exclusively in sequential fire mode. Unlike some nail guns, it does not support bump fire mode. To fire a nail, the nosepiece must be fully depressed before pulling the trigger, ensuring…

Battery capacity plays a key role in nail firing performance on the RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer. The total number of nails driven per charge depends on the amp-hour (Ah) rating of the battery, with higher Ah batteries…

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer features a magazine that holds a single strip of nails, with capacity depending on nail diameter: 70 nails for 2.87mm, 67 nails for 3.03mm, and 60 nails for 3.33mm nails.

For…

To maintain peak performance, the internal air reservoir of the RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer may need topping up after firing approximately 20,000–25,000 nails.

For safe air replenishment, first remove the battery…

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer features a fast 1-second ramp-up time, enabling nails to be fired quickly with minimal delay between each shot. This ensures efficient, smooth, and precise framing, making it ideal for high-speed…

Easily control how deep nails are driven with your RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer. To adjust nail depth:

Locate the depth adjustment dial near the nosepiece of the tool.

Rotate the dial anti-clockwise…

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer operates in sequential fire mode for controlled and precise fastening. To begin, activate the tool by squeezing the grip switch beneath the main trigger. The LED indicator will illuminate green…

To load nails, point the nailer forward and insert a strip of nails into the magazine. Pull the tensioner fully back and release it to lock the nails in place. For removing unused nails, follow the instructions in the guide: How to Remove Unused…

To ensure smooth, trouble-free operation, maintain your RYOBI 18V ONE+ HP Brushless Framing Nailer after each use or every 3,000 nails. Key maintenance steps include:

Lubricate the Firing Pin: Apply a few drops of pneumatic tool oil…

To operate a RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, first position the nosepiece where you want to drive the nail. Press the tool to compress the nosepiece. The nosepiece must be fully depressed combined with the grip switch, or the…

The RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer operates in sequential fire mode for controlled and precise fastening. To begin, activate the tool by squeezing the grip switch beneath the main trigger. The LED indicator will illuminate green…

If there is a nail jammed in your RYOBI 18V ONE+ HP Brushless 30-34° Framing Nailer, the LED will flash red to indicate it’s in jam protection mode. To remove the nail, first remove the battery - this will reset the tool. Using the on-board Allen…

To safely remove unused nails from the RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer, pull back the retainer to release tension on the nail strip. Then, press the side lever to allow the nails to slide out of the magazine.

This…

To maintain peak performance, the internal air reservoir of the RYOBI 18V ONE+ HP Brushless 30–34° Framing Nailer may need topping up after firing approximately 20,000–25,000 nails.

For safe air replenishment, first remove the battery…